close

Вход

Забыли?

вход по аккаунту

?

MANUAL - Hertz

код для вставкиСкачать
HCP
ADWANCED
WEB
MANUAL
AMPLIFIER
www.hertzaudiovideo.com
Esec_AWM Amplificatori HCP_preliminary.indd 1
20/06/13 17:03
HCP
Advanced Web Manual
Index
1.PRECAUTIONS................................................................................................................................. 3
2. INSTALLATION AND SIZES............................................................................................................ 4
3. CABLE SIZE CALCULATION TABLES. 1: POWER SUPPLY / 2: SPEAKERS............................ 4
4. POWER SUPPLY and REMOTE IN CONNECTION / FUSE REPLACEMENT.......................... 5
5. SUBWOOFER REMOTE VOLUME CONTROL: HRC installation.............................................. 5
6. PRE IN / SPEAKER IN / PRE OUT................................................................................................. 6
7. AUTO TURN-ON BY SPEAKER IN (without REMOTE IN) ........................................................... 8
8. INSTALLATION EXAMPLES:
HCP 1D:(1CH) FILTERED SUBWOOFER........................................................................................... 10
(1CH) FULL RANGE SINGLE CHANNEL............................................................................. 11
HCP 2: (2CH) FRONT L / R............................................................................................................. 12
(1CH) SUBWOOFER L+R.................................................................................................... 13
(1CH) SUBWOOFER MONO INPUT.................................................................................... 14
HCP 4: (4CH) FRONT + REAR........................................................................................................ 15
(3CH) FRONT + SUB.......................................................................................................... 16
(2CH) LEFT / RIGHT............................................................................................................ 17
HCP 4D:(4CH) FRONT + REAR........................................................................................................ 18
(4CH) WOOFER + MID/HI................................................................................................... 19
(3CH) FRONT + SUB.......................................................................................................... 20
(2CH) LEFT / RIGHT............................................................................................................ 21
HCP 5D:(5CH) FRONT + REAR + SUB............................................................................................. 22
(5CH) WOOFER + TW + SUB............................................................................................. 23
(3CH) FRONT + SUB.......................................................................................................... 24
9. BLOCK DIAGRAMS
HCP 1D:........................................................................................................................................... 25
HCP 2: ........................................................................................................................................... 25
HCP 4: ........................................................................................................................................... 26
HCP 4D:........................................................................................................................................... 27
HCP 5D:........................................................................................................................................... 28
10.TECHNICAL SPECIFICATIONS
HCP 1D:........................................................................................................................................... 29
HCP 2: ........................................................................................................................................... 29
HCP 4: ........................................................................................................................................... 30
HCP 4D:........................................................................................................................................... 30
HCP 5D:........................................................................................................................................... 31
:
Not
AVAILABLE
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
2
Esec_AWM Amplificatori HCP_preliminary.indd 2
20/06/13 17:03
HCP
Advanced Web Manual
1 PRECAUTIONS
Before installing the components, please carefully read all of the instructions contained in this manual. It is advisable to
carefully follow the highlighted instructions. Failure to respect these instructions may cause unintentional harm or damage
to the components.
SAFETY CONSIDERATIONS
1. Make sure your car has 12 VDC voltage negative ground electric system.
2. Check your alternator and battery condition to ensure they can handle the increased consumption.
3. Do not carry out any installation inside the engine compartment or exposed to water, excessive humidity, dust or dirt.
4. Never run cables outside the vehicle or install the amplifier next to electronic gearcases.
5. Install the amplifier in the vehicle parts where temperature is between 0В°C (32В°F) and 55В°C (131В°F). Let the amplifier outer profile be
at least 5 cm (2”) far from possible walls. There must be good air circulation where the amplifier is installed. If you cover the heat sink,
the amplifier goes in protection.
6. The amplifier can reach temperatures of around 80В°C (176В°F). Make sure it is not dangerously hot before touching it.
7. Periodically clean the amplifier without using aggressive solvents that might damage it. Don’t use compressed air, since it would push
solid parts in the amplifiers. Dampen a piece of cloth with water and soap, wring it and clean the amplifier. Then use a piece of cloth
dampened with water only; eventually clean the amplifier with a dry piece of cloth.
8. Make sure the location you chose for the components does not affect the correct functioning of the vehicle mechanical and electrical devices.
9. Make sure power cable is not short circuited during installation and connection with the battery.
10. Use extreme caution when cutting or drilling the car plate, checking there are no electrical wiring or structural element underneath.
11. When positioning the power supply cable, avoid to run the wire over or through sharp edges or close to moving mechanical devices.
Use rubber grommets to protect the wire if it runs in a hole of the plate or proper materials if it is close to heat-generating parts.
12. Make sure all the cables are properly secured all along their length. Also, make sure their outer protective jacket is flame resistant and self
extinguishing. Use a clamping screw to secure positive and negative cables just close to the amplifier respective power supply
terminal blocks.
13. Choose the cable gauge according to the amplifier power and to the suggestions you can find here. Use high quality cables, connectors
and accessories, as you can find in the Connection catalogue.
14. Pre-plan the configuration of your new amplifier and the best wiring routes to ease installation.
15. In order to avoid incidental damage, keep the product in the original packaging until you are ready for the final installation.
16. Always wear protective eyewear when using tools, as splints or product residue may become airborne.
TYPICAL INSTALLATION SEQUENCE
If you have any questions please refer to the Advanced Manual you can find available on www.hertzaudiovideo.com or contact your Hertz
dealer or Hertz authorized service for assistance.
1. Before installing the amplifier turn off the source and all other electronic devices in the audio system to prevent any damages.
2. Using a cable with adequate AWG (see chart: Power Supply Cable), run the power wire from the battery location to the amplifier
mounting location.
3. Connect the power supply with the correct polarity. connect (+) terminal to the cable coming from the battery and (-) terminal to the car chassis.
4. Put an insulated fuse holder 40 cm max far from the battery positive terminal; connect one end of the power cable to it after
connecting the other end to the amplifier. Do not mount the fuse.
5. To ground the device (-) in the right way, use a screw in the vehicle chassis; scrape all paint or grease from the metal if necessary,
checking with a tester that there is continuity between the battery negative terminal (-) and the fixing point. If possible, connect all
components to the same ground point; this solution rejects most noise which can be generated during the audio reproduction.
6. Route all signal cables close together and away from power cables.
7. Connect the RCA input cables, the applied signal must be between 0.3 VRMS and 5 VRMS.
8. Connect the high level inputs using the proper plug. Applied signal must be between 1 VRMS and 22 VRMS. Don’t use it if you are
already using Pre In preamplified connection.
9. Connect the speaker output using 10 AWG max speaker cable.
10. Don’t connect (-) L and (-) R speaker outputs together. If you use an external stereo crossover, make sure that its negative poles are
not connected together.
11. The amplifier turns on by connecting the remote turn on terminal (REMOTE IN) to the source specific output. The amplifier turns on
automatically, without remote signal, also if using high level inputs (Speaker IN) by setting the “AUTO TURN ON” switch to position ON.
12. The LED on the front panel lights up green indicating that the product is on. The LED lights up red if the outputs go on overload, if the
thermal protection is triggered, if the speaker cables short circuit with the vehicle chassis and if the amplifier is malfunctioning.
13. The fuse/s is/are located near the power supply and speaker terminals. To replace, remove the fuse/s from the housing. Always replace
the fuse of the same rating.
14. Secure all auxiliary devices you built to install the components to the vehicle structure; this insures stability and safety while driving.
The amplifier detachment while driving can seriously damage the people in the vehicle and other cars.
15. When installation is over, check the system’s wiring and make sure all connections were done in the right way.
16. Put the fuse into the fuse holder. The fuse value will have to be 30% higher than the amplifier built-in one. In case the cable supplies
several amplifiers, the fuse value will have to be 30% higher than the sum of the values of all other fuses in the amplifiers.
17. Listening level calibration is made by adjusting the source volume up to 3/4 of its maximum level; then, adjust the amplifier levels until
you hear distortion.
SAFE SOUND
USE COMMON SENSE AND PRACTICE SAFE SOUND. PLEASE REMEMBER THAT LONG EXPOSURE TO EXCESSIVELY HIGH
SOUND PRESSURE LEVELS MAY DAMAGE YOUR HEARING. SAFETY MUST BE AT THE FOREFRONT WHILE DRIVING.
Information on electrical and electronic equipment waste (for those European countries which organize the separate collection of waste)
Products which are marked with a wheeled bin with an X through it can not be disposed of together with ordinary domestic waste. These electrical and
electronic products must be recycled in proper facilities, capable of managing the disposal of these products and components. In order to know where and
how to deliver these products to the nearest recycling/disposal site please contact your local municipal office. Recycling and disposing of waste in a proper
way contributes to the protection of the environment and to prevent harmful effects on health.
3
Esec_AWM Amplificatori HCP_preliminary.indd 3
20/06/13 17:03
HCP
Advanced Web Manual
2 INSTALLATION AND SIZES
A
B
B
C
D
E
HCP 1D
215200190 166 50mm
8.467.877.48 6.531.97in.
HCP 2
215200190 166 50mm
8.467.877.48 6.531.97in.
HCP 4
315291190 166 50mm
12.40 11.45 7.48 6.53 1.97 in.
HCP 4D
215200190 166 50mm
8.467.877.48 6.531.97in.
HCP 5D
345321190 166 50mm
13.58 12.64 7.48 6.53 1.97 in.
A
D
C
E
3 CABLE SIZE CALCULATION TABLES:
1: Power supply cable / 2: Speakers cable
1: Power supply cable
*Current Draw I (A)
Applied power
Cable diameter
2: Speakers cable
Connection length
Cable Length (m)
4
Esec_AWM Amplificatori HCP_preliminary.indd 4
20/06/13 17:03
HCP
Advanced Web Manual
4 POWER SUPPLY and REMOTE IN CONNECTION / FUSE REPLACEMENT
GND
REM +12V
FUSE
FUSE REPLACE WARNING:
firmly press contacts of each
fuse into their fuse-holder clips
POWER
20
APPLY A FUSE CLOSE
TO BATTERY POSITIVE POLE
TO PROTECT BATTERY CABLE
GND
AMPLIFIER FUSE
(see Tech. Spec.)
16 mm / 0.62 in.
16 mm / 0.62 in.
REMOTE OUT
FUSE
POWER SUPPLY
POWER SUPPLY
12 mm / 0.47 in.
12 mm / 0.47 in.
CAR BATTERY
SOURCE
REMOTE
REMOTE
GND
5 SUBWOOFER REMOTE VOLUME CONTROL: HRC INSTALLATION
HCP 1D
SUBWOOFER
REMOTE VOLUME CONTROL
OPTIONAL
HRC
HCP 5D
SUBWOOFER
REMOTE VOLUME CONTROL
OPTIONAL
HRC
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 5
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
5
20/06/13 17:03
HCP
Advanced Web Manual
6 PRE IN / SPEAKER IN / PRE OUT
HCP 1D
R
HI-IN
USE PRE-IN
OR HI-IN:
NOT BOTH
HI-LEVEL OUTPUT
L
PRE OUT
SOURCE
R
PRE IN
PRE OUTPUT
L
HCP 2
R
USE PRE-IN
OR HI-IN:
NOT BOTH
HI-LEVEL OUTPUT
L
HI-IN
SOURCE
PRE OUT
R
If using
FRONT INPUT OFF
only, select:
HCP 4
PRE OUTPUT
L
PRE IN
If using
REAR INPUT ON
select:
R
HI-IN
FRONT
FOR EACH INPUT
(FRONT - REAR )
USE PRE-IN
OR HI-IN :
NOT BOTH
L
HI-IN
REAR
SOURCE
PRE OUT
(FRONT CHANNELS)
R
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 6
PRE OUTPUT
L
PRE IN PRE IN
FRONT REAR
:
HI-LEVEL OUTPUT
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
6
20/06/13 17:03
HCP
Advanced Web Manual
If using
FRONT INPUT OFF
only, select:
HCP 4D
If using
REAR INPUT ON
select:
R
FOR EACH INPUT
(FRONT - REAR)
USE PRE-IN
OR HI-IN:
NOT BOTH
L
SOURCE
PRE OUT
(FRONT CHANNELS)
PRE IN
FRONT
HCP 5D
HI-LEVEL OUTPUT
HI-IN HI-IN
FRONT REAR
R
PRE OUTPUT
L
PRE IN
REAR
If using
FRONT INPUT
only, select:
WARNING: Using 3CH mode
REAR INPUT is not available
OFF
If using
REAR INPUT
select:
ON
If NOT using
SUB INPUT, OFF
select:
If using
SUB INPUT, ON
select:
R
HI-LEVEL OUTPUT
FOR EACH INPUT
(FRONT - REAR - SUB)
USE PRE-IN
OR HI-IN:
NOT BOTH
HI-IN
FRONT
HI-IN
REAR
HI-IN
SUB
L
SOURCE
R
PRE OUTPUT
PRE IN
FRONT
PRE IN
REAR
:
L
PRE IN
SUB
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 7
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
7
20/06/13 17:03
HCP
Advanced Web Manual
7 AUTO TURN ON BY SPEAKER IN (without REMOTE IN)
HCP 1D
ON
INPUT
L R
HCP 2
ON
INPUT
L R
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 8
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
8
20/06/13 17:03
HCP
Advanced Web Manual
HCP 4 / HCP 4D
ON
INPUT
L R
HCP 5D
INPUT
L R
ON
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 9
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
9
20/06/13 17:03
HCP
Advanced Web Manual
8 INSTALLATION EXAMPLES
1CH: FILTERED SUBWOOFER
INPUTS:
HCP 1D
SUB
LEVEL
SUB
LO PASS
ON
USE PRE-IN
OR HI-IN
INPUT
INPUT
L R
R
SOURCE
L
OUTPUTS:
12 mm / 0.62 in.
SUBWOOFER
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 10
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
10
20/06/13 17:03
HCP
Advanced Web Manual
1CH: FULL RANGE - SINGLE CHANNEL
INPUTS:
HCP 1D
LEVEL
OFF
USE PRE-IN
OR HI-IN
INPUT
INPUT
L R
R
SOURCE
L
OUTPUTS:
FULL RANGE SYSTEM
MONO
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 11
:
Set-up
CONTROLS
12 mm / 0.62 in.
:
Adjustment
CONTROLS
11
20/06/13 17:03
HCP
Advanced Web Manual
2CH: FRONT L / R
INPUTS:
HCP 2
FRONT
LEVELS
HI 80
OFF
INPUT
USE PRE-IN
OR HI-IN
INPUT
L R
R
SOURCE
L
OUTPUTS:
12 mm / 0.62 in.
PASSIVE FILTERS
L
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 12
:
Set-up
CONTROLS
R
:
Adjustment
CONTROLS
12
20/06/13 17:03
HCP
Advanced Web Manual
1CH: SUBWOOFER L+R
INPUTS:
HCP 2
SUB
LEVEL
OFF
INPUT
USE PRE-IN
OR HI-IN
SUB
LO PASS
LO
INPUT
L R
R
SOURCE
L
OUTPUTS:
12 mm / 0.62 in.
SUBWOOFER
(L+R)
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 13
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
13
20/06/13 17:03
HCP
Advanced Web Manual
1CH: SUBWOOFER - MONO INPUT
INPUTS:
HCP 2
ON
FULL
SUB
LEVEL
AUDIO PROCESSOR
SUBWOOFER CHANNEL
OUTPUTS:
12 mm / 0.62 in.
SUBWOOFER
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 14
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
14
20/06/13 17:03
HCP
Advanced Web Manual
4CH: FRONT + REAR
INPUTS:
HCP 4
FRONT
LEVELS
HI 80
OFF
HI 80
FRONT
INPUT
FRONT
INPUT
USE PRE-IN
OR HI-IN
OFF
OFF
OFF
REAR
LEVELS
L R
R
SOURCE
L
Using also REAR INPUTS:
ON
REAR
INPUT
REAR
INPUT
activate
REAR
INPUT
USE PRE-IN OR HI-IN
OUTPUTS:
L
R
FRONT
REAR
12 mm / 0.62 in.
R
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 15
:
Set-up
CONTROLS
L
:
Adjustment
CONTROLS
15
20/06/13 17:03
HCP
Advanced Web Manual
3CH: FRONT + SUB
INPUTS:
HCP 4
FRONT
LEVELS
OFF
USE PRE-IN
OR HI-IN
FRONT
INPUT
HI 80
OFF
LO
OFF
SUB
FRONT
INPUT
LEVEL
LO PASS
L R
R
SOURCE
L
Using also REAR INPUTS to drive SUBWOOFER:
ON
activate
REAR
SUB INPUT
INPUT
SUB
INPUT
USE PRE-IN OR HI-IN
OUTPUTS:
SUBWOOFER
(L+R)
12 mm / 0.62 in.
L
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 16
:
Set-up
CONTROLS
PASSIVE FILTERS
FRONT
:
Adjustment
CONTROLS
R
16
20/06/13 17:03
HCP
Advanced Web Manual
2CH: LEFT / RIGHT
INPUTS:
HCP 4
L
LEVEL
ON
L
HI 80
ON
HI 80
ON
L
R
LEVEL
L
R
R
SOURCE
L
USE PRE-IN OR HI-IN
OUTPUTS:
12 mm / 0.62 in.
PASSIVE FILTERS
L
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 17
:
Set-up
CONTROLS
R
:
Adjustment
CONTROLS
17
20/06/13 17:03
HCP
Advanced Web Manual
4CH: FRONT + REAR
INPUTS:
HCP 4D
FRONT
LEVELSHI-PASS
OFF
USE PRE-IN
OR HI-IN
FRONT
INPUT
FRONT
INPUT
HI
OFF
HI
OFF
REAR
LEVELHI-PASS
L R
R
SOURCE
L
Using also REAR INPUTS:
ON
REAR
INPUT
REAR
INPUT
activate
REAR
INPUT
USE PRE-IN OR HI-IN
OUTPUTS:
L
R
FRONT
REAR
12 mm / 0.62 in.
R
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 18
:
Set-up
CONTROLS
L
:
Adjustment
CONTROLS
18
20/06/13 17:03
HCP
Advanced Web Manual
4CH: WOOFER + MID/HI
INPUTS:
HCP 4D
MID/HI
LEVELSHI-PASS
OFF
USE PRE-IN
OR HI-IN
FRONT
INPUT
FRONT
INPUT
HI
OFF
LO
OFF
WOOFER
LEVELSLO-PASS
L R
R
SOURCE
L
OUTPUTS:
PASSIVE FILTERS
L
R
MID / HI
WOOFER
L
R
PASSIVE FILTERS
12 mm / 0.62 in.
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 19
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
19
20/06/13 17:03
HCP
Advanced Web Manual
3CH: FRONT + SUB
INPUTS:
HCP 4D
MID/HI
LEVELSHI-PASS
OFF
USE PRE-IN
OR HI-IN
FRONT
INPUT
FRONT
INPUT
HI
OFF
LO
OFF
SUBWOOFER
LEVELLO-PASS
L R
R
SOURCE
L
Using also REAR INPUTS to drive SUBWOOFER:
ON
SUB
INPUT
SUB
INPUT
activate
REAR
INPUT
USE PRE-IN OR HI-IN
OUTPUTS:
SUBWOOFER
(L+R)
PASSIVE FILTERS
FRONT
12 mm / 0.62 in.
L
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 20
:
Set-up
CONTROLS
R
:
Adjustment
CONTROLS
20
20/06/13 17:03
HCP
Advanced Web Manual
2CH: LEFT / RIGHT
INPUTS:
HCP 4D
L
LEVELHI-PASS
ON
L
L
L
HI
ON
HI
ON
R
LEVELHI-PASS
R
R
SOURCE
L
USE PRE-IN OR HI-IN
OUTPUTS:
12 mm / 0.62 in.
PASSIVE FILTERS
L
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 21
:
Set-up
CONTROLS
R
:
Adjustment
CONTROLS
21
20/06/13 17:03
HCP
Advanced Web Manual
5CH: FRONT + REAR + SUB
INPUTS:
HCP 5D
FRONT
LEVELSHI-PASS
HI
REAR
LEVELSHI-PASS
5CH OFF
X1
HI
OFF
USE PRE-IN
OR HI-IN
FRONT
INPUT
FRONT
INPUT
SUBWOOFER
LEVELLO-PASS
L R
R
SOURCE
L
Using also REAR / SUB INPUTS:
ON
ON
activate
SUB
INPUT
REAR
INPUT
REAR
INPUT
SUB
INPUT
activate
REAR
INPUT
SUB
INPUT
USE PRE-IN OR HI-IN
OUTPUTS:
SUBWOOFER
L
R
FRONT
REAR
R
12 mm / 0.62 in.
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 22
:
Set-up
CONTROLS
L
:
Adjustment
CONTROLS
22
20/06/13 17:03
HCP
Advanced Web Manual
5CH: WOOFER + TWEETER + SUB
INPUTS:
HCP 5D
WOOFER
TWEETER
LEVELSHI-PASS LO-PASS LEVELSHI-PASS
HI
X10
5CH
BAND
OFF
USE PRE-IN
OR HI-IN
SUBWOOFER
LEVELLO-PASS
L R
R
SOURCE
L
OUTPUTS:
SUBWOOFER
L
R
TWEETER
WOOFER
R
L
12 mm / 0.62 in.
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 23
:
Set-up
CONTROLS
:
Adjustment
CONTROLS
23
20/06/13 17:03
HCP
Advanced Web Manual
3CH: FRONT + SUB
INPUTS:
HCP 5D
FRONT
LEVELSHI-PASS
HI
X1
3CH
OFF
USE PRE-IN
OR HI-IN
SUBWOOFER
LEVELLO-PASS
L R
R
SOURCE
L
OUTPUTS:
SUBWOOFER
PASSIVE FILTERS
FRONT
12 mm / 0.62 in.
L
:
Not
AVAILABLE
Esec_AWM Amplificatori HCP_preliminary.indd 24
:
Set-up
CONTROLS
R
:
Adjustment
CONTROLS
24
20/06/13 17:03
Esec_AWM Amplificatori HCP_preliminary.indd 25
+6dB
INPUT
(1.5 - 12V)
PREOUT
(0.6 - 5V)
RCA prot
HRC
(optional)
OFF
(L - MONO IN)
R
L
0 dB
RCA prot
R
L
ART
L
R
L
R
ART
AUTO
TURN ON
OFF
ON
SUB Volume
REMOTE
CONTROL
HI-PASS
50 Hz 250
12 dB
AUTO
TURN ON
OFF
ON
LEVEL
MIN MAX
LEVELS
MIN MAX
to REMOTE IN
L+R
to REMOTE IN
80 Hz
12 dB
LO-PASS
50 Hz 250
LO-PASS
50 Hz 500
12 dB
HI-PASS
VCA
12 dB
PASS MODE
HI
FULL LO
FILTER
OFF
ON
180
Deg.
BOOST 50Hz
+6dB
0dB +12dB
PHASE
0
R
L
BOOST
0 dB +12
25 Hz
(IN L) MONO
OFF
ON
SUBSONIC
OFF
ON
24 dB
L
AMP
R
AMP
AMP
OUT
LEFT
OUT
RIGHT
OUT
HCP 1D
HI-IN
PREOUT
(0,6 - 5V)
PRE-IN
INPUT
(1,5 - 12V)
HI-IN
HCP
Advanced Web Manual
9 BLOCK DIAGRAMS
HCP 2
25
20/06/13 17:03
Esec_AWM Amplificatori HCP_preliminary.indd 26
(0.6 - 5V)
PRE-IN
(L - MONO IN)
REAR IN
(1.5 - 12V)
HI-IN
PREOUT
(0.6 - 5V)
PRE-IN
(L - MONO IN)
FRONT IN
(1.5 - 12V)
HI-IN
RCA prot
RCA prot
L
R
L
R
L
R
ART
REAR IN
OFF
ON
(REAR)
AUTO
TURN ON
OFF
ON
LEVELS
MIN MAX
(REAR)
LEVELS
MIN MAX
(FRONT)
to REMOTE IN
LO-PASS
50 Hz 500
12 dB
(REAR)
HI-PASS
80 Hz
12 dB
(REAR)
LO-PASS
50 Hz 500
12 dB
(FRONT)
HI-PASS
80 Hz
12 dB
(FRONT)
PASS MODE
HI
FULL LO
(REAR)
PASS MODE
HI
FULL LO
(FRONT)
BOOST 50Hz
+6dB
0dB +12dB
(REAR)
R
L
R
L
(FRONT)
(IN L) MONO
OFF
ON
(REAR)
(IN L) MONO
OFF
ON
L
AMP
R
AMP
L
AMP
R
AMP
OUT
LEFT
REAR
OUT
RIGHT
OUT
LEFT
FRONT
OUT
RIGHT
HCP
Advanced Web Manual
HCP 4
26
20/06/13 17:03
Esec_AWM Amplificatori HCP_preliminary.indd 27
(0.6 - 5V)
PRE-IN
(L - MONO IN)
REAR IN
(1.5 - 12V)
HI-IN
PREOUT
(0.6 - 5V)
PRE-IN
(L - MONO IN)
FRONT IN
(1.5 - 12V)
HI-IN
RCA prot
RCA prot
L
R
L
R
L
R
ART
REAR IN
OFF
ON
(REAR)
AUTO
TURN ON
OFF
ON
Hz
3.2k
FILTER
LEVELS
3.2k
50
Hz
12 dB
(REAR)
FILTER
50
12 dB
(FRONT)
MIN MAX
(REAR)
LEVELS
MIN MAX
(FRONT)
to REMOTE IN
LO
HI
LO
HI
PASS MODE
HI
FULL LO
(REAR)
PASS MODE
HI
FULL LO
(FRONT)
BOOST 50Hz
0 dB +12
50 Hz
(REAR)
R
L
R
L
(FRONT)
(IN L) MONO
OFF
ON
(REAR)
(IN L) MONO
OFF
ON
L
AMP
R
AMP
L
AMP
R
AMP
OUT
LEFT
REAR
OUT
RIGHT
OUT
LEFT
FRONT
OUT
RIGHT
HCP
Advanced Web Manual
HCP 4D
27
20/06/13 17:03
Esec_AWM Amplificatori HCP_preliminary.indd 28
(0.6 - 5V)
PRE-IN
SUB IN
(1.5 - 12V)
HI-IN
(0.6 - 5V)
PRE-IN
REAR IN
(1.5 - 12V)
HI-IN
(0.6 - 5V)
PRE-IN
(3CH IN)
FRONT IN
HI-IN
(1.5 - 12V)
+6dB
R
L
R
L
HRC
(optional)
OFF
0 dB
RCA prot
RCA prot
RCA prot
R
L
ART
SUB Volume
REMOTE
CONTROL
INPUT
OFF
ON
(SUB)
INPUT
OFF
ON
(REAR)
AUTO
TURN ON
OFF
ON
L+R
MIX
to REMOTE IN
(FRONT)
LO
HI
LO-PASS
LEVEL
24 dB
(SUB)
HI-PASS
BAND: HI-PASS
50 Hz 500
12 dB
(REAR)
MULTIPLIER
Frequencyes
x1
x 10
50 Hz 500
VCA
HI-PASS
LO
HI
BAND: LO-PASS
50 Hz 500
12 dB
(FRONT)
MIN MAX
(SUB)
LEVELS
MIN MAX
(REAR)
LEVELS
MIN MAX
(FRONT)
(FRONT)
BOOST
0 dB +12
50 Hz
(SUB)
MODE
HI
FULL BAND
(REAR)
MODE
FULL
HI
L
R
L
R
25 Hz
SUBSONIC
OFF
ON
24 dB
(SUB)
AMP MODE
5ch
3ch
AMP
R
AMP
L
AMP
R
AMP
L
AMP
OUT
LEFT
OUT
RIGHT
REAR
OUT
LEFT
OUT
RIGHT
FRONT
5CH:
OUT
SUB
+
-
(NC)
+
-
(NC)
L
R
(NC)
(NC)
3CH:
HCP
Advanced Web Manual
HCP 5D
28
20/06/13 17:03
HCP
Advanced Web Manual
10 TECHNICAL SPECIFICATIONS
HCP 1D
HCP 2
Power Supply
Power Supply
Power supply voltage / fuse: 11Г·15 VDC / 2 x 25 A
Idling current (power ON/OFF): 1 A / 0.04 mA
Consumption @ 2Ω, 14.4 VDC
(Max Musical Power): 25 A
Remote In: ART: 7 Г· 15 VDC - 1 mA
Automatic Remote Turn-On/Off with Speaker-In
Amplifier Stage
Power supply voltage / fuse: 11Г·15 VDC / 1 x 20 A
Idling current (power ON/OFF): 0. 4 A / 0.04 mA
Consumption @ 2Ω, 14.4 VDC
(Max Musical Power): 12 A
Remote In: ART : 7 Г· 15 VDC - 1 mA
Automatic Remote Turn-On/Off with Speaker-In
Amplifier Stage
Features:
Features:
Distorsion - THD (100 Hz @ 4Ω): 0.02 %
Bandwidth: 10 Г· 22k Hz
S/N Ratio (A weighted @ 1 V): 100 dB
Damping factor (100 Hz @ 4Ω): 80
Distorsion - THD (100 Hz @ 4Ω): 0.01 %
Bandwidth: 10 Г· 65k Hz
S/N Ratio (A weighted @ 1 V): 103 dB
Damping factor (100 Hz @ 4Ω): 200
Pre-In sensitivity: 0.6 ÷ 5 VRMS (15 kΩ)
Pre-In sensitivity: 0.6 ÷ 5 VRMS (15 kΩ)
Speaker-In sensitivity: 1.5 ÷ 12 VRMS (47Ω)
Speaker-In sensitivity: 1.5 ÷ 12 VRMS (47Ω)
Load impedance (MIN):
2Ω
Load impedance (MIN)@ 2 Ch:
@ 1 Ch:
Output Power (RMS) @ 14.4 VDC, THD 1%:
Output Power (RMS) @ 14.4 VDC, THD 1%:
1 Ch:
320 W x 1 (4Ω)
2 Ch:
1 Ch: 550 W x 1 (2Ω)
2 Ch: 85 W x 2 (2Ω)
1 Ch:
170 W x 1 (4Ω)
2Ω
4Ω
55 W x 2 (4Ω)
Output Power (RMS) @ 14.4 VDC, THD 10%:
1 Ch:
380 W x 1 (4Ω)
Output Power (RMS) @ 14.4 VDC, THD 10%:
1 Ch: 700 W x 1 (2Ω)
2 Ch:
65 W x 2 (4Ω)
2 Ch: 100 W x 2 (2Ω)
1 Ch:
200 W x 1 (4Ω)
CEA 2006-A Ratings:
RMS Power
(4Ω,≤1 %THD+N, 14.4 V): 300 W x 1 Ch
S/N Ratio (ref. 1 W output):
CEA 2006-A Ratings:
80 dBA
RMS Power
(4Ω,≤1 %THD+N, 14.4 V): 50 W x 2 Ch
Inputs / Outputs / Filter
S/N Ratio (ref. 1 W output):
INPUTS:
PRE IN / SPEAKER IN
Inputs / Outputs / Filter
Preout Hi-Pass:
50 Г· 250 Hz @ 12 dB/Oct.
82 dBA
Filters FULL:
Lo-Pass: Yes
50 Г· 250 Hz @ 24 dB/Oct.
SUBSONIC (on/off):
25 Hz @ 24 dB/Oct.
BOOST 50 Hz (adjust):
(0 Г· 12) dB
PHASE (adjust):
(0 Г· 180) deg
Filters FULL:
Hi-Pass: Lo-Pass: (-50 Г· 6) dB
MONO (on/off):
Yes
BOOST 50 Hz (select):
(0 / 6 / 12) dB
Remote Volume Control (adjust):
Size / Weight
INPUTS:
PRE IN / SPEAKER IN
Preout FULL range (FRONT):
Yes
Yes
80 Hz @ 12 dB/Oct.
50 Г· 500 Hz @ 12 dB/Oct.
Size / Weight
Max size (mm / in.): 215 x 190 x 50 / 8.46” x 7.48” x 1.97”
Weight (kg / lb.):
1,94 / 4.27
Max size (mm / in.): 215 x 190 x 50 / 8.46” x 7.48” x 1.97”
Weight (kg / lb.):
1,80 / 3.96
29
Esec_AWM Amplificatori HCP_preliminary.indd 29
20/06/13 17:03
HCP
Advanced Web Manual
HCP 4
HCP 4D
Power Supply
Power Supply
Power supply voltage / fuse: 11Г·15 VDC / 2 x 20 A
Idling current (power ON/OFF): 1 A / 0.04 mA
Consumption @ 2Ω, 14.4 VDC
(Max Musical Power): Remote In: ART:
21 A
7 Г· 15 VDC - 1 mA
Automatic Remote Turn-On/Off with Speaker-In
Power supply voltage / fuse: 11Г·15 VDC / 2 x 20 A
Idling current (power ON/OFF): 1.6 A / 0.04 mA
Consumption @ 2Ω, 14.4 VDC
(Max Musical Power): Remote In: ART: 22 A
7 Г· 15 VDC - 1 mA
Automatic Remote Turn-On/Off with Speaker-In
Amplifier Stage
Amplifier Stage
Features:
Features:
Distorsion - THD (100 Hz @ 4Ω): 0.01 %
Bandwidth: 10 Г· 45K Hz
S/N Ratio (A weighted @ 1 V): 103 dB
Damping factor (100 Hz @ 4Ω): 120
Distorsion - THD (100 Hz @ 4Ω): 0.02 %
Bandwidth: 10 Г· 60K Hz
S/N Ratio (A weighted @ 1 V): 100 dB
Damping factor (100 Hz @ 4Ω): 200
Pre-In sensitivity: 0.6 ÷ 5 VRMS (15 kΩ)
Pre-In sensitivity: 0.6 ÷ 5 VRMS (15 kΩ)
Speaker-In sensitivity: 1.5 ÷ 12 VRMS (47Ω)
Speaker-In sensitivity: 1.5 ÷ 12 VRMS (47Ω)
Load impedance (MIN)@ 4 Ch:
2Ω
@ 3 Ch:
2Ω + 2Ω + 4Ω
@ 2 Ch:
4Ω
Load impedance (MIN)@ 4 Ch:
2Ω
@ 3 Ch:
2Ω + 2Ω + 4Ω
@ 2 Ch:
4Ω
Output Power (RMS) @ 14.4 VDC, THD 1%:
Output Power (RMS) @ 14.4 VDC, THD 1%:
4 Ch:
55 W x 4 (4Ω)
4 Ch:
75 W x 4 (4Ω)
4 Ch:
85 W x 4 (2Ω)
4 Ch:
130 W x 4 (2Ω)
3 Ch:
55 W x 2 (4Ω) + 170 W x 1 (4Ω)
3 Ch:
75 W x 2 (4Ω) + 260 W x 1 (4Ω)
3 Ch:
85 W x 2 (2Ω) + 170 W x 1 (4Ω)
3 Ch:
130 W x 2 (2Ω) + 260 W x 1 (4Ω)
2 Ch:
170 W x 2 (4Ω)
2 Ch:
260 W x 2 (4Ω)
Output Power (RMS) @ 14.4 VDC, THD 10%:
Output Power (RMS) @ 14.4 VDC, THD 10%:
4 Ch:
65 W x 4 (4Ω)
4 Ch:
85 W x 4 (4 Ω)
4 Ch:
95 W x 4 (2Ω)
4 Ch:
145 W x 4 (2 Ω)
3 Ch:
65 W x 2 (4Ω) + 190 W x 1 (4Ω)
3 Ch:
85 W x 2 (4 Ω) + 290 W x 1 (4 Ω)
3 Ch:
95 W x 2 (2Ω) + 190 W x 1 (4Ω)
3 Ch:
145 W x 2 (2 Ω) + 290 W x 1 (4 Ω)
2 Ch:
190 W x 2 (4Ω)
2 Ch:
290 W x 2 (4 Ω)
CEA 2006-A Ratings:
CEA 2006-A Ratings:
RMS Power (4Ω,≤1 %THD+N, 14.4 V): 50 W x 4 Ch
RMS Power (4Ω,≤1 %THD+N, 14.4 V): 70 W x 4 Ch
S/N Ratio (ref. 1 W output):
S/N Ratio (ref. 1 W output):
82 dBA
Inputs / Outputs / Filter
INPUTS :
80 dBA
Inputs / Outputs / Filter
PRE IN / SPEAKER IN
Preout FULL range (FRONT):
Yes
INPUTS :
Preout FULL range (FRONT):
PRE IN / SPEAKER IN
Yes
FRONT Ch. filters FULL:
Yes
Hi-Pass:80 Hz @ 12 dB/Oct.
Lo-Pass:
50 Г· 500 Hz @ 12 dB/Oct.
FRONT Ch. filters FULL:
Yes
Hi-Pass:
50 Г· 3.2k Hz @ 12 dB/Oct.
Lo-Pass:
50 Г· 3.2k Hz @ 12 dB/Oct.
REAR Ch. filters FULL:
Yes
Hi-Pass:80 Hz @ 12 dB/Oct.
Lo-Pass:
50 Г· 500 Hz @ 12 dB/Oct.
REAR Ch. filters FULL:
Yes
Hi-Pass:
50 Г· 3.2k Hz @ 12 dB/Oct.
Lo-Pass:
50 Г· 3.2k Hz @ 12 dB/Oct.
FRONT Ch. MONO (on/off):
Yes
FRONT Ch. MONO (on/off):
REAR Ch. MONO (on/off):
Yes
REAR Ch. MONO (on/off):
Yes
BOOST 50 Hz (select):
(0 / 6 / 12) dB
BOOST 50 Hz (select):
(0 Г· 12) dB
Size / Weight
Yes
Size / Weight
Max size (mm / in.): 315 x 190 x 50 / 12.40” x 7.48” x 1.97”
Max size (mm / in.): 215 x 190 x 50 / 8.46” x 7.48” x 1.97”
Weight (kg / lb.):
Weight (kg / lb.):
2,62 / 5.77
1,94 / 4.27
30
Esec_AWM Amplificatori HCP_preliminary.indd 30
20/06/13 17:03
HCP
Advanced Web Manual
HCP 5D
Power Supply
Power supply voltage / fuse: 11Г·15 VDC / 2 x 25 A
Idling current (power ON/OFF): 2 A / 0.04 mA
Consumption @ 2Ω, 14.4 VDC
(Max Musical Power): 30 A
Remote In: ART:
7 Г· 15 VDC - 1 mA
Automatic Remote Turn-On/Off with Speaker-In
Amplifier Stage
Features:
Distorsion - THD (100 Hz @ 4Ω): 0.02 %
Bandwidth FRONT/REAR: 10 Г· 50k Hz
Bandwidth SUB: 10 Г· 500 Hz
S/N Ratio (A weighted @ 1 V): 100 dB
Damping factor (100 Hz @ 4Ω) FRONT/REAR: 100
Damping factor (100 Hz @ 4Ω) SUB: 250
Pre-In sensitivity: 0.6 ÷ 5 VRMS (15 kΩ)
Speaker-In sensitivity: 1.5 ÷ 12 VRMS (47Ω)
Load impedance (MIN)@ 5 Ch:
2Ω
@ 3 Ch:
4Ω + 4Ω + 2Ω
Output Power (RMS) @ 14.4 VDC, THD 1%:
5 Ch:
55 W x 4 + 160 W x 1 (4Ω)
5 Ch:
90 W x 4 + 280 W x 1 (2Ω)
3 Ch:
180 W x 2 (4Ω) + 160 W x 1 (4Ω)
3 Ch:
180 W x 2 (4Ω) + 280 W x 1 (2Ω)
Output Power (RMS) @ 14.4 VDC, THD 10%:
5 Ch:
65 W x 4 + 200 W x 1 (4Ω)
5 Ch:
105 W x 4 + 330 W x 1 (2Ω)
3 Ch:
210 W x 2 (4Ω) + 200 W x 1 (4Ω)
3 Ch:
210 W x 2 (4Ω) + 330 W x 1 (2Ω)
CEA 2006-A Ratings:
RMS Power (4Ω,≤1 %THD+N, 14.4 V): 50 W x 4 Ch + 150 W + 1 Ch
S/N Ratio (ref. 1 W output):
(50 W Ch) 83 dBA
(150 W Ch) 83 dBA
Inputs / Outputs / Filter
INPUTS:
PRE IN / SPEAKER IN
FRONT Ch. filters FULL:
Yes
Hi-Pass:
50 Г· 5k Hz @ 12 dB/Oct.
REAR Ch. filters FULL:
Yes
Hi-Pass:
50 Г· 500 Hz @ 12 dB/Oct.
Band-Pass:
50 Г· 500 Hz (hi) @ 12 dB/Oct.
50 Г· 5kHz (lo) @ 12 dB/Oct.
SUB Ch. filter LO-PASS:
50 Г· 500 Hz @ 24 dB/Oct.
SUBSONIC (on/off):
BOOST 50 Hz (adjust):
Remote Volume Control (adjust):
25 Hz @ 24 dB/Oct.
(0 Г· 12) dB
(-50 Г· 6) dB
Size / Weight
Max size (mm / in.): 345 x 190 x 50 / 13.58” x 7.48” x 1.97”
Weight (kg / lb.):
2,61 / 5.75
31
Esec_AWM Amplificatori HCP_preliminary.indd 31
20/06/13 17:03
All Specifications Subject to Change Without Notice
13.REV.B
PART OF ELETTROMEDIA - 62018 Potenza Picena (MC) Italy - T +39 0733 870 870 - F +39 0733 870 880 - www.elettromedia.it
Esec_AWM Amplificatori HCP_preliminary.indd 32
20/06/13 17:03
Документ
Категория
Без категории
Просмотров
49
Размер файла
4 533 Кб
Теги
1/--страниц
Пожаловаться на содержимое документа