close

Вход

Забыли?

вход по аккаунту

?

Subject: date: July 8th, 2002 How to download new - Monarch

код для вставки
Subject:
How to download new firmware for 64xx / DPM / ALX-92x
date:
by:
July 8th, 2002
OEM-Int. Tech. Support/JI
This procedure shows, how to perform in case of unregular behavior of the printer when downloading firmware.
Pls. see the service manual (on CD-ROM) for detailed instructions.
Firmware Download 64 bit
The printer is
ok, and you want to update
the firmware?
Yes
Standard firmware
update:
"SYSTEM.BAT"
No
Yes
.
Can the
printer be switched to
ONLINE?
Confirm that
meassage
and switch to
ONLINE
No
Was it
successfull?
Start the "Forced mode"
(press and hold
CUT, FEED, ESC
and turn power on
Yes
No
End
Yes
Does
the display show
"Status 6004:Load H8
programm" ?
No
Goto
"Bootloader mode"
on next page
C:\Documents and Settings\Kelly Below\My Documents\Monarch-EMEA\support\documents\64xx_FirmwareDownload.doc page 1
of 4
Bootloader mode
Start the "Bootloader mode"
(press and hold CUT and ESC
and turn power on)
Does the
display show "Boot Loader
Vx.x 115KBaud/Centro."
?
No
No
Does the
display show "Boot Loader
Vx.x 115200 Baud"
?
Replace the
CPU-Board
Yes
Yes
Bootloader firmware Download: Use
the utility programm "download.exe".
Connect printer to Com1
"DOWNLOAD RISC.S3B"
Bootloader firmware Download:
"copy RISC.S3B LPT1 /b"
Was it
successfull?
Yes
Switch the printer to
ONLINE and run the
Standard firmware update:
"SYSTEM.BAT"
No
Goto
"Clear Parameter"
C:\Documents and Settings\Kelly Below\My Documents\Monarch-EMEA\support\documents\64xx_FirmwareDownload.doc page 2
of 4
Clear Parameter
You see probably messages like
"Version changed" or
"Unmgd.Interrupt" or
"Param.Update"
Start the "Bootloader mode"
(press and hold CUT and ESC
and turn power on)
Does the
display show "Boot Loader
Vx.x 115KBaud/Centro."
?
No
Does the
display show "Boot Loader
Vx.x 115200 Baud"
?
No
Replace the
CPU-Board
Yes
Yes
Erase the parameterbuffers: *
Connect printer to LPT1
- "Copy CLRPARA1.S3B LPT1 /b"
- "Copy CLRPARA2.S3B LPT1 /b"
-"Copy RISC.S3B LPT1 /b"
- System.bat
* Note: youВґll find that
"CLRPARA*.S3B files"
on Docu CD-ROM in
Subdirectory Utilities ...
Erase the parameterbuffers: *
Use of utility programm "download.exe
Connect printer to Com1
- "DOWNLOAD CLRPARA1.S3B"
- "DOWNLOAD CLRPARA2.S3B"
- "DOWNLOAD RISC.S3B"
- System.bat
Caution!
Because all, really all !! parameters,
are cleared now,
set at least the most important parameters:
-HRES
- PRINTERTYPE
- PERIPH.DEVICE
- HEAD STEP TUNE
End
C:\Documents and Settings\Kelly Below\My Documents\Monarch-EMEA\support\documents\64xx_FirmwareDownload.doc page 3
of 4
Additional informations to the 64xx firmware:
The firmware includes the following files:
-
Std.exe
H8.s3b
Risc.s3b
Ave256.s3b
Spd-x50.s3b
= the file, you can get from internet = self extracting file, it creates:
(not needed for standard firmware update)
(without fonts, without H8; not needed for standard firmware update)
(Fixed size Fonts)
(scalable Speedo-fonts)
-
Std.s3b
(it contains "everything" and includes also the files H8.s3b; Risc.s3b; fonts)
System.bat
(it executes the file "Std.s3b" with the DOS-command "copy STD.s3b lpt1 /b")
Download.exe (not included now, probably in the future, "utility"-program for bootloader)
Firmware download via Flash-Card:
-
Rename the file "STD.S3B" to "AUTOSTRT.FOR"
Copy that "AUTOSTRT.FOR" -file to a Flash-Card. Use a notebook to do that.
Insert that Flash-Card to the 64-bit printer and turn on the printer: The new firmware is downloaded
within appr. 30 seconds.
C:\Documents and Settings\Kelly Below\My Documents\Monarch-EMEA\support\documents\64xx_FirmwareDownload.doc page 4
of 4
Документ
Категория
Без категории
Просмотров
0
Размер файла
29 Кб
Теги
1/--страниц
Пожаловаться на содержимое документа